on 06-28-2013 2:12 PM
Dear Friends!
We are working day & night in an Oil & Gas project.
We are currently in the data migration phase, where we are creating the materials into the ECC box.
I am using the Idoc OILMAT05 to create the material master; the material master is getting successfully created however I can see that there are some minors issues!
1. The Additional Units of Measure is not getting updated; we have the data in the input file.
We want these data to be updated as shown in the screen shot using the idoc methodology!
2. The OIL-specific view is not getting created; we have the data in the input file.
Please see the screen-shot!
Any ideas on these issues!
Regards
Tanmoy
this is result, now share the details of your idoc
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.
Hello Jurgen!
Don't you think '009' will be more relevant?
003 Delete: Message contains objects to be deleted
004 Change: Message contains changes
005 Replace: This message replaces previous messages
009 Original: First message for process
023 Wait/Adjust: Data should not be imported
018 Resend
Regards
Tanmoy
Hello Jurgen;
I was away from this thread for some time now. Well the isssue is partially solved.
I am using the following values proposed by SAP; Please see the table given below:
X | Aun | <=> | Y | Bun |
1 | BB6 | <=> | 1 | BB6 |
87.602 | L | <=> | 551 | BB6 |
87.602 | L15 | <=> | 551 | BB6 |
12.64 | KG | <=> | 100 | BB6 |
6.87 | M15 | <=> | 43.211 | BB6 |
6.87 | M3 | <=> | 43.211 | BB6 |
79 | TO | <=> | 625 | BB6 |
Please note that 12.64 KG <=> 100 BB6 is working fine, in fact when we see the newly created material using MM03; the value taken by SAP is 13 KG instead of 12.64 KG.
Well for the rest of the conversion values in the table above; it is going to errors & saying -
Regards
Tanmoy
Hello Jurgen!
First of all a Many Thanks to you for your great support.
I am sharing the final results & closing the thread.
Please see the table below for conversions of Alternate UOM:
MEINH_MARM | UMREZ | UMREN | MESUB | GEWEI_MARM |
L | 551 | 87602 | BB6 | KG |
L15 | 551 | 87602 | BB6 | KG |
KG | 100 | 12.640 | BB6 | KG |
M15 | 43211 | 6870 | BB6 | KG |
KG | 100 | 12.640 | BB6 | KG |
L | 551 | 87602 | BB6 | KG |
L15 | 551 | 87602 | BB6 | KG |
M15 | 43211 | 6870 | BB6 | KG |
Moreover;
Incase we want to trouble-shhot; we can put a break-point at the following source:
Program = SAPLMGD1; Include = EAN_UCC_ROUTINES |
The function module -
EAN150_MARM_CHECK_CONSISTENCY |
- It corrects the values for Alternate UOM
Many Thanks
Tanmoy
Message was edited by: Tanmoy Mondal
User | Count |
---|---|
107 | |
12 | |
11 | |
6 | |
5 | |
4 | |
4 | |
3 | |
3 | |
3 |
You must be a registered user to add a comment. If you've already registered, sign in. Otherwise, register and sign in.